How to remove and install a hood release cable and Hood Latch on Subaru Outback?

On 2008 and later models, remove the front bumper cover. Scribe a line around the latch to aid alignment when installing. Detach the latch retaining bolts from the radiator support and remove the latch. Note the routing of the hood release cable, then disengage the cable from the latch assembly. Installation is the reverse of removal. Disconnect the hood release cable from the latch assembly as described above. Attach a piece of stiff wire to the end of the cable. Trace the cable back to the firewall and detach all cable retaining clips. On earlier models, remove the knee bolster. Remove the hood release lever retaining screws. Disengage the cable from the hood release lever. Pull the old cable into the passenger compartment until you can see the stiff wire that you attached to the cable. A grommet insulates the cable hole in the firewall from the elements. The new cable should have a new grommet, so you can remove and discard the old cable grommet. Make sure the new grommet is already on the new cable, then detach the old cable from the wire and attach the new cable to the wire. Working from the engine compartment side of the firewall, pull the wire through the cable hole in the firewall. Installation is otherwise the reverse of the removal. Working in the passenger compartment, push the grommet into place with your fingers. Make sure it's fully seated in the hole in the firewall.

Genuine Subaru Outback Hood Release Cable

Hood Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Hood Release Cables found

View related parts
Subaru Outback Cable Assembly Front Hd
Part Number: 57330AJ00A
$69.00 MSRP: $100.00
You Save: $31.00 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable-Front Hood
- Position: Front
- Replaced by: 57330AJ00C
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2010-2014 Subaru Outback | 2.5GT Limited, 2.5GT Premium, 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Sport, 2.5i Touring, 3.6R, 3.6R Limited, 3.6R Premium, 3.6R Touring | 2.5L H4 DOHC, 2.5L H4 SOHC, 2.5L H4 Turbo, 3.6L H6
View related parts
Subaru Outback Cable Assembly Front Hd SIA
Part Number: 57330AL04A
$14.48 MSRP: $20.98
You Save: $6.50 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable-Front Hood; Release Cable
- Position: Front
- Replaces: 57330AL00B, 57330AL00A
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2015-2019 Subaru Outback | 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Sport, 2.5i Touring, 3.6R, 3.6R Limited, 3.6R Premium, 3.6R Touring | 2.5L H4, 3.6L H6
View related parts
Subaru Outback Cable Assembly Front Hd
Part Number: 57330AJ00C
$69.00 MSRP: $100.00
You Save: $31.00 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable-Front Hood; Release Cable
- Position: Front
- Replaces: 57330AJ00A
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2010-2014 Subaru Outback | 2.5GT Limited, 2.5GT Premium, 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Sport, 2.5i Touring, 3.6R, 3.6R Limited, 3.6R Premium, 3.6R Touring | 2.5L H4 DOHC, 2.5L H4 SOHC, 2.5L H4 Turbo, 3.6L H6
View related parts
Subaru Outback Cable Assembly Hood
Part Number: 57330AL00A
$14.48 MSRP: $20.98
You Save: $6.50 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable-Front Hood
- Position: Front
- Replaced by: 57330AL04A
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2015 Subaru Outback | 2.5i, 2.5i Limited, 2.5i Premium, 3.6R, 3.6R Limited, 3.6R Premium | 2.5L H4, 3.6L H6
View related parts
Subaru Outback Cable Assembly Front Hd LHD
Part Number: 57330AG09A
Product Specifications
- Other Name: Cable-Front Hood; Release Cable
- Position: Front
- Replaces: 57330AG11A
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2005-2009 Subaru Outback | 2.5i, 2.5i Base, 2.5i Limited, 3.0R, 3.0R Limited, 3.0R LL-Bean, Base, GT, GT Limited, XT Limited | 2.5L H4, 2.5L H4 Turbo, 3.0L H6
View related parts
Subaru Outback Cable Assembly Front Hood
Part Number: 57330AE00AGE
Product Specifications
- Other Name: Cable-Front Hood; Release Cable
- Position: Front
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2000-2004 Subaru Outback | Base, Cold Weather, Flat6, Flat6 L.L.Bean, Flat6-S, GT, Limited, SUS Flat6, SUS Limited | 2.5L H4, 3.0L H6
View related parts
Subaru Outback Cable Assembly Front Hood
Part Number: 57330AE00AOA
Product Specifications
- Other Name: Cable-Front Hood; Release Cable
- Position: Front
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2000-2004 Subaru Outback | Baja, Baja-B, Baja-S, Base, Brighton, Cold Weather, Flat6, GT, L, Limited, L-S, SUS Flat6, SUS Limited | 2.5L H4, 2.5L H4 Turbo, 3.0L H6
View related parts
Subaru Outback Hood Cable Assembly
Part Number: 57330AC070MU
Product Specifications
- Other Name: Cable-Front Hood; Release Cable
- Position: Front
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1996-1997 Subaru Outback | Brighton, GT, L, LS, LS-I, Out Back, Post, SUS | 2.2L H4 , 2.2L H4 (New EVAPO), 2.5L H4
View related parts
Subaru Outback Hood Cable Assembly
Part Number: 57330AC070RA
Product Specifications
- Other Name: Cable-Front Hood
- Position: Front
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1996 Subaru Outback | Brighton, GT, L, LS, LS-I, Out Back | 2.2L H4 , 2.2L H4 (New EVAPO), 2.5L H4
View related parts
Subaru Outback Hood Cable Assembly
Part Number: 57330AC040MU
Product Specifications
- Other Name: Cable-Front Hood; Release Cable
- Position: Front
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1996 Subaru Outback | Brighton, GT, L, LS, LS-I, Out Back, Post | 2.2L H4 , 2.5L H4
View related parts
Subaru Outback Hood Cable Assembly
Part Number: 57330AC040RA
Product Specifications
- Other Name: Cable-Front Hood
- Position: Front
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1996 Subaru Outback | Brighton, GT, L, LS, LS-I, Out Back, Post | 2.2L H4 , 2.5L H4
View related parts
Subaru Outback Hood Cable Assembly
Part Number: 57330AC070ML
Product Specifications
- Other Name: Cable-Front Hood; Release Cable
- Position: Front
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1998-1999 Subaru Outback | Brighton, GT, L, LS, Out Back, Post, SUS | 2.2L H4 , 2.2L H4 (New EVAPO), 2.2L H4 Series, 2.5L H4

Subaru Outback Hood Release Cable

Our website stands as the go-to online destination for OEM Subaru Outback Hood Release Cable. With complete lines of genuine Subaru Outback Hood Release Cable available at unbeatable market prices, we ensure top quality, reliability, and durability. Each part comes backed by the manufacturer's warranty, reinforcing your trust in our offerings.

Subaru Outback Hood Release Cable Parts Questions & Experts Answers

Cable Assembly Front Hd SIA
57330AL04A
Q: How to remove and install a hood release cable and Hood Latch on Subaru Outback?
A: On 2008 and later models, remove the front Bumper cover. Scribe a line around the latch to aid alignment when installing. Detach the latch retaining bolts from the radiator support and remove the latch. Note the routing of the hood release cable, then disengage the cable from the latch assembly. Installation is the reverse of removal. Disconnect the hood release cable from the latch assembly as described above. Attach a piece of stiff wire to the end of the cable. Trace the cable back to the firewall and detach all cable retaining clips. On earlier models, remove the knee bolster. Remove the hood release lever retaining screws. Disengage the cable from the hood release lever. Pull the old cable into the passenger compartment until you can see the stiff wire that you attached to the cable. A grommet insulates the cable hole in the firewall from the elements. The new cable should have a new grommet, so you can remove and discard the old cable grommet. Make sure the new grommet is already on the new cable, then detach the old cable from the wire and attach the new cable to the wire. Working from the engine compartment side of the firewall, pull the wire through the cable hole in the firewall. Installation is otherwise the reverse of the removal. Working in the passenger compartment, push the grommet into place with your fingers. Make sure it's fully seated in the hole in the firewall.