How Do You Replace a Master Cylinder on Subaru Outback?

Place some shop rags underneath the brake master cylinder to catch any spilled brake fluid, then remove the brake fluid from the reservoir. Unplug the electrical connector from the brake fluid level indicator and place some rags or newspapers under the brake line fittings. Using a flare-nut wrench, unscrew the brake line tube nuts and allow any residual fluid to drain onto the rags. Remove the brake master cylinder-to-power brake booster mounting nuts and remove the brake master cylinder from the engine compartment. If a new brake master cylinder is being installed, the power brake booster pushrod length must be checked and adjusted. Bench bleed the new brake master cylinder before installing it, attach a pair of brake master cylinder bleeder tubes to the outlet ports of the brake master cylinder, fill the reservoir with brake fluid, slowly push the pistons into the brake master cylinder, remove the bleed tubes, one at a time and install plugs in the open ports to prevent fluid leakage and air from entering, replace the O-ring seal on the brake master cylinder, thread the brake line fittings into the brake master cylinder, fill the brake master cylinder reservoir with fluid, then bleed the brake master cylinder and the brake system, have an assistant depress the brake pedal and hold the pedal to the floor, loosen the fitting just enough to allow air and fluid to escape then tighten it lightly, repeat this procedure on both fittings until the fluid is clear of air bubbles and then tighten the fittings securely, rinse the area under the brake master cylinder with clean water, fully tighten the mounting nuts, then the brake line fittings, tighten the brake master cylinder mounting nuts, and test the operation of the brake system carefully before placing the vehicle into normal service.

Genuine Subaru Outback Brake Master Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

26 Brake Master Cylinders found

View related parts
Subaru Outback Master Cylinder Assembly (VDC)
Part Number: 26401AJ000
$168.65 MSRP: $246.57
You Save: $77.92 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder Assembly
- Replaced by: 26401AJ002
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2010-2014 Subaru Outback | 2.5GT Limited, 2.5GT Premium, 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Sport, 2.5i Touring, 3.6R, 3.6R Limited, 3.6R Premium, 3.6R Touring | 2.5L H4 DOHC, 2.5L H4 SOHC, 2.5L H4 Turbo, 3.6L H6
View related parts
Subaru Outback Master Cylinder Assembly
Part Number: 26401AC220
$329.46 MSRP: $481.67
You Save: $152.21 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 26401AC191
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1998-2003 Subaru Outback | Baja, Baja-S, Base, Brighton, Cold Weather, Flat6, Flat6 L.L.Bean, GT, L, Limited, LS, Out Back, SUS, SUS Flat6, SUS Limited | 2.2L H4 , 2.2L H4 (New EVAPO), 2.5L H4, 3.0L H6
View related parts
Subaru Outback Master Cylinder Assembly (VDC)
Part Number: 26401AG030
$165.63 MSRP: $242.15
You Save: $76.52 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder Assembly; Master Cylinder
- Replaced by: 26401AG031
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2005-2009 Subaru Outback | 2.5i, 2.5i Base, 2.5i Limited, 3.0R, 3.0R Limited, 3.0R LL-Bean, Base, GT, GT Limited, XT Limited | 2.5L H4, 2.5L H4 Turbo, 3.0L H6
View related parts
Subaru Outback Master Cylinder Assembly
Part Number: 26401AE03A
$329.46 MSRP: $481.67
You Save: $152.21 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder
- Replaced by: 26401AC191
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2003-2004 Subaru Outback | Baja, Baja-S, Base, Brighton, Cold Weather, Flat6, Flat6 L.L.Bean, Flat6-S, GT, L, Limited, L-S, SUS Flat6, SUS Limited | 2.5L H4, 3.0L H6
View related parts
Subaru Outback Ma Cylinder Assembly (VDC)LH
Part Number: 26401AJ001
$168.65 MSRP: $246.57
You Save: $77.92 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder Assembly
- Replaced by: 26401AJ002
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2014 Subaru Outback | 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Sport, 2.5i Touring, 3.6R, 3.6R Limited, 3.6R Premium, 3.6R Touring | 2.5L H4 DOHC, 3.6L H6
View related parts
Subaru Outback Master Cylinder Kit
Part Number: 26449AL03A
$153.98 MSRP: $225.12
You Save: $71.14 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2016-2021 Subaru Outback | 2.4R F/R-O, 2.4R Limited, 2.4R Touring, 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Sport, 2.5i Touring, 3.6R, 3.6R Limited, 3.6R Premium, 3.6R Touring | 2.4L H4 DIT, 2.5L H4, 2.5L H4 DI, 3.6L H6
View related parts
Subaru Outback WVY35 Master Cylinder Kit
Part Number: 26449FJ011
$181.07 MSRP: $264.72
You Save: $83.65 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder Kit; Master Cylinder
- Replaced by: 26449FJ013
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2015-2017 Subaru Outback | 2.5i, 2.5i Limited, 2.5i Premium, 2.5i Sport, 2.5i Touring, 3.6R, 3.6R Limited, 3.6R Premium | 2.5L H4, 3.6L H6
View related parts
Subaru Outback Master Cylinder Assembly
Part Number: 26401AC200
$175.35 MSRP: $256.37
You Save: $81.02 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 26401AC121
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1998 Subaru Outback | Brighton, L | 2.2L H4 , 2.2L H4 (New EVAPO)
View related parts
Subaru Outback Master Cylinder Assembly
Part Number: 26401AA241
$125.33 MSRP: $181.63
You Save: $56.30 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Master Cylinder
- Replaced by: 26401AA242
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1996 Subaru Outback | L | 2.2L H4
View related parts
Subaru Outback Master Cylinder Assembly
Part Number: 26401AC120
$175.35 MSRP: $256.37
You Save: $81.02 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 26401AC121
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1999 Subaru Outback | Brighton | 2.2L H4 Series
View related parts
Subaru Outback Master Cylinder Assembly (Abs)
Part Number: 26401AG010
$146.41 MSRP: $214.05
You Save: $67.64 (32%)
Product Specifications
- Other Name: Master Cylinder Assembly; Master Cylinder
- Replaced by: 26401AG011
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2005-2009 Subaru Outback | 2.5i, 2.5i Limited, 3.0R, 3.0R LL-Bean, Base, GT, GT Limited | 2.5L H4, 2.5L H4 Turbo, 3.0L H6
View related parts
Subaru Outback Master Cylinder Assembly
Part Number: 26401AC100
Product Specifications
- Replaced by: 26401AC101
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1997-1999 Subaru Outback | Post | 2.2L H4 (New EVAPO), 2.2L H4 Series
View related parts
Subaru Outback Master Cylinder Assembly
Part Number: 26401AE010
Product Specifications
- Replaced by: 26401AE011
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2001-2003 Subaru Outback | Flat6, SUS Flat6 | 3.0L H6
View related parts
Subaru Outback Master Cylinder Assembly LH
Part Number: 26401AE02A
Product Specifications
- Other Name: Master Cylinder Assembly
- Replaced by: 26401AE02B
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2000-2001 Subaru Outback | Brighton | 2.5L H4
View related parts
Subaru Outback Master Cylinder Assembly LH
Part Number: 26401AE02B
Product Specifications
- Other Name: Master Cylinder Assembly; Master Cylinder
- Replaces: 26401AE02A
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2004 Subaru Outback | Baja-B | 2.5L H4 Turbo
- 2000-2001 Subaru Outback | Brighton | 2.5L H4
View related parts
Subaru Outback Master Cylinder Assembly
Part Number: 26401AC020
Product Specifications
- Replaced by: 26401AA232
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1996-1997 Subaru Outback | Brighton, L | 2.2L H4 , 2.2L H4 (New EVAPO)
View related parts
Subaru Outback Master Cylinder Assembly
Part Number: 26401AC230
Product Specifications
- Replaced by: 26401AC231
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1999 Subaru Outback | L | 2.2L H4 Series
View related parts
Subaru Outback Master Cylinder Assembly
Part Number: 26401AA231
Product Specifications
- Replaced by: 26401AA232
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1996 Subaru Outback | Brighton, L | 2.2L H4
View related parts
Subaru Outback Master Cylinder Assembly
Part Number: 26401AE011
Product Specifications
- Other Name: Master Cylinder
- Replaces: 26401AE010
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 2001-2004 Subaru Outback | Flat6, SUS Flat6 | 3.0L H6
View related parts
Subaru Outback P1140696 Master Cylinder
Part Number: 26401AA201
Product Specifications
- Other Name: Master Cylinder Assembly
- Replaced by: 26401AA202
- Warranty: This genuine part is guaranteed by Subaru's factory warranty.
Fits the following Vehicles:
- 1996 Subaru Outback | Post | 2.2L H4 , 2.2L H4 (New EVAPO)

| Page 1 of 2 |Next >

1-20 of 26 Results

Subaru Outback Brake Master Cylinder

Our website stands as the go-to online destination for OEM Subaru Outback Brake Master Cylinder. With complete lines of genuine Subaru Outback Brake Master Cylinder available at unbeatable market prices, we ensure top quality, reliability, and durability. Each part comes backed by the manufacturer's warranty, reinforcing your trust in our offerings.

Subaru Outback Brake Master Cylinder Parts Questions & Experts Answers

Master Cylinder Assembly
26401AC100
Q: How Do You Replace a Master Cylinder on Subaru Outback?
A: Place some shop rags underneath the brake master cylinder to catch any spilled brake fluid, then remove the brake fluid from the reservoir. Unplug the electrical connector from the brake fluid level indicator and place some rags or newspapers under the brake line fittings. Using a flare-nut wrench, unscrew the brake line tube nuts and allow any residual fluid to drain onto the rags. Remove the brake master cylinder-to-power Brake Booster mounting nuts and remove the brake master cylinder from the engine compartment. If a new brake master cylinder is being installed, the power brake booster pushrod length must be checked and adjusted. Bench bleed the new brake master cylinder before installing it, attach a pair of brake master cylinder bleeder tubes to the outlet ports of the brake master cylinder, fill the reservoir with brake fluid, slowly push the pistons into the brake master cylinder, remove the bleed tubes, one at a time and install plugs in the open ports to prevent fluid leakage and air from entering, replace the O-ring seal on the brake master cylinder, thread the brake line fittings into the brake master cylinder, fill the brake master cylinder reservoir with fluid, then bleed the brake master cylinder and the brake system, have an assistant depress the brake pedal and hold the pedal to the floor, loosen the fitting just enough to allow air and fluid to escape then tighten it lightly, repeat this procedure on both fittings until the fluid is clear of air bubbles and then tighten the fittings securely, rinse the area under the brake master cylinder with clean water, fully tighten the mounting nuts, then the brake line fittings, tighten the brake master cylinder mounting nuts, and test the operation of the brake system carefully before placing the vehicle into normal service.

Genuine Subaru Outback Brake Master Cylinder

26 Brake Master Cylinders found

Subaru Outback Master Cylinder Assembly (VDC)

Subaru Outback Master Cylinder Assembly

Subaru Outback Master Cylinder Assembly (VDC)

Subaru Outback Master Cylinder Assembly

Subaru Outback Ma Cylinder Assembly (VDC)LH

Subaru Outback Master Cylinder Kit

Subaru Outback WVY35 Master Cylinder Kit

Subaru Outback Master Cylinder Assembly

Subaru Outback Master Cylinder Assembly

Subaru Outback Master Cylinder Assembly

Subaru Outback Master Cylinder Assembly (Abs)

Subaru Outback Master Cylinder Assembly

Subaru Outback Master Cylinder Assembly

Subaru Outback Master Cylinder Assembly LH

Subaru Outback Master Cylinder Assembly LH

Subaru Outback Master Cylinder Assembly

Subaru Outback Master Cylinder Assembly

Subaru Outback Master Cylinder Assembly

Subaru Outback Master Cylinder Assembly

Subaru Outback P1140696 Master Cylinder

Subaru Outback Brake Master Cylinder

Subaru Outback Brake Master Cylinder Parts Questions & Experts Answers

Related Subaru Outback Parts

Browse by Year